Car Key Button Repair

A damaged car key is a hassle. You might need to contact an emergency locksmith service or purchase an alternative remote key fob repairs.

But, you may be saving money by repairing an old key fob instead of replacing it. This is particularly true if the problem is caused by the worn-out switch or defective contact.

Battery

If your key fob's buttons are not responding to your pressing them, it could be a sign that the battery has failed or is close to the end of life. Fortunately, replacing the battery is an easy task that you can complete on your own instead of hiring a locksmith to complete the task for you.

Locate the battery compartment first. The battery compartment is typically located on the back of the key fob and may be hidden behind a cover that opens or an open button that opens the access point. When the compartment is open then look for the small button-cell battery. It's usually shaped as coins and identified with the plus and minus signs. Remove the old battery and replace it with a new one. Check that the plus and the minus symbols are properly aligned.

Close the compartment and snap the two parts of your key fob. Before closing the door, align and snap the pieces into the correct position. To ensure that the buttons work properly Press any of them.

If the remote keyfob isn't working after replacing the battery, there could be other issues that require a different kind of repair. Physical damage caused by dropping the device in a puddle for instance could cause it to stop working completely. It could also be experiencing an electrical issue within the device or it may require to be deprogrammed by an expert or locksmith. Check out these other common auto troubleshooting techniques to determine if your key fob is having a problem of its own.

Switches

There are many kinds of switches used in the car key repairs near me key fob according to the year and make. The older model of key often has a separate chip that you can see in the case, while the modern keys are more sophisticated and work by sending signals to the car. No matter what type of key, the keys' buttons can become worn out or damaged with normal use. The result is they become difficult to press, or even ineffective. If you attempt to force the button to function it could cause further damage and potentially stop the key from starting your vehicle in the future.

If your key doesn't appear to be working, you should first try changing the battery. If that doesn't work then you might need to clean your key fob and re-adjust the switches. Since these tiny electronic switches are constantly being tossed around, they are more likely to break down than the larger components of your key.

The switches are made of rubber, and are coated with an electricity conducting film that wears down over time. However, they're small and easy to replace. The old ones are soldered onto the circuit board, and you'll have to take care to remove them without causing damage to other parts. You can then solder new ones into and then reassemble your fob.

One way to prevent your car key fob from being ruined is to avoid using it for more than a few hours at a time and to keep it out of the way in areas that it will be visible. Also, you should find a secure location to keep your key in when you aren't making use of it.

If the problem persists after you've cleaned the key fob replaced the battery and tried to clean it, then you may need to consult a locksmith. A professional can check the frequency of your key to see whether it's still able communicate with your vehicle, open and replace micro switches, swap cases and much more.

Outer Case

Key fobs spend many hours bouncing around, and when the buttons aren't able to move between the case, they could become stuck or break. If cleaning the case with rubbing alcohol and a cotton swab does not work, it could be necessary to remove the case. If the contacts that the buttons touch are not suitable for the application or are worn, changing them might be the only solution.

Rubber buttons may be worn out over time. The rubber expands, nails gouge into it and the buttons can become difficult to press. This could cause the key to fail and, in this situation, it's time for a new case or new buttons. This repair involves disassembling your remote car key repair, finding the switch on the board, then heating the solder, and carefully removing them. New buttons are then attached to the circuit board. The case can be reassembled and the mobile key repair blade of the horseshoe can be attached. The new buttons should be snugly fitted into the case to prevent them falling out.

Inner Case

Since your key fob is prone to be tossed around and could sometimes be accidentally pressed, the buttons inside can become stuck or broken over time. With the help of metallic tape and a hole punch you can often quickly fix this problem when your car is away from home when the key fob doesn't work, allowing you to unlock the doors, but not start the engine. This quick fix could allow you to safely make it back to your vehicle and complete your journey.